Clopay Torsion Spring Replacement Nationwide

Clopay Torsion Spring Replacement: The Long Beach Owner’s Guide

We stock and install Clopay-compatible torsion springs from our service vehicles across Long Beach, and most replacements run between $180 and $340 installed, including the spring, labor, and a written scope before we start. Same-day replacement is typically available for standard 2-inch springs on 7-foot doors, and the most common phone call we get starts the same way: a bang from the garage that sounded like a car backfiring, followed by a door that won’t lift more than a few inches. The torsion spring is the counterweight system mounted on a steel tube above your door opening, and when it breaks, the door’s full weight is suddenly unassisted.

Call (424) 688-6426

Which Clopay Models This Applies To

Clopay builds torsion spring systems across three residential lines you’ll see throughout Long Beach: the Classic series (steel and raised-panel doors), the Gallery series (insulated steel), and the Reserve and Canyon Ridge lines (wood-look and carriage-house doors). The torsion spring itself is matched to the door’s weight and height, not the model name. A 7-foot Clopay double door with polyurethane insulation needs a different spring pair than a 7-foot single non-insulated door, and we confirm this by measuring the existing spring’s wire diameter, coil length, and inside diameter before ordering or pulling a replacement from the truck.

One Clopay-specific gotcha: some newer Clopay doors ship with TorqueMaster spring systems, a closed-tube design that looks nothing like a standard exposed torsion spring. If you see a square or round tube with no visible coils above the door, you have a TorqueMaster system, and replacement parts and labor for that run differently than standard torsion. We service both, but we’ll confirm what you have before quoting. We’re an independent service provider and not affiliated with Clopay, which means we can quote OEM-equivalent springs or quality aftermarket options side by side and let the stamped wire gauge and cycle-life rating make the argument.

Signs Your Clopay Torsion Spring Replacement Is Failing

• You heard a loud snap or bang from the garage. This is the spring breaking under tension, usually when the door is closed. One of the two springs has failed; the other is now carrying the full load and will fail soon too.
• The door won’t open more than a few inches. A broken torsion spring removes the counterbalance, meaning the motor or your own arms are now trying to lift 150 to 200 pounds of door with no mechanical advantage.
• The door feels heavy or lopsided when operated manually. Before a full break, fatigue cracks inside the coil let the spring unwind slightly, so the door leans toward the heavier corner or grinds against its tracks.
• You can see a visible gap in the spring coil. Torsion springs break cleanly across a coil; if you look up and see a two-inch separation where the wire used to be continuous, that’s the failure point, and it’s not repairable.
• The opener motor runs hard, strains, or trips its overload protector. An under-tensioned or broken spring forces the operator to absorb weight it was never designed to handle, burning through motor wear cycles and stripping gears prematurely.

Before

After

Replacement Cost & What’s Included

In Long Beach, Clopay torsion spring replacement lands between $180 and $340 installed. Single-spring systems on standard 7-foot doors sit at the lower end. Double-spring configurations, high-cycle springs rated for 25,000 or more cycles, or doors over 7 feet tall run toward the upper end. The spring itself is typically 40 to 50 percent of the quote; the rest is labor, balance adjustment after installation, and a tension test across the full travel of the door.

Every quote we hand over includes the spring cost, the labor, and the written scope of work as a flat number, not an estimate with a floating range. There’s no hourly meter running and no “it turned out to be worse than we thought” addendum after the fact. If we quote $290 on a Clopay single-spring replacement, that’s the invoice: $290. Clause 1 of The Haven Standard is the flat written price before any work begins, and we’ve operated under it since 2015. The replacement carries our 365-Day Done Right Promise: if the spring fails in the first year due to our installation, we make it right without charging you to redo the work.

DIY or Call Us?

Torsion springs are under several hundred pounds of torque in an unwound state alone, and when a spring lets go during manipulation, it moves with enough force to break bone or worse. This is not a scare line; it’s the reason the repair trade treats spring work as a two-person, trained-technician job with proper winding bars and drill-in-depth controls. What an owner can safely do is identify the failure: photograph the broken spring, note whether you have one spring or two, measure the door height, and release the opener from the door using the red emergency cord so nothing else strains against the broken counterbalance.

What you shouldn’t do is attempt to unwind or replace the spring yourself. The winding bars, the set screws under load, the cable tension balancing: each involves a stored-energy hazard that training and repetition exist to manage. Marcus Deller would rather explain why a neighbor’s garage door had been held together with zip ties for three years than watch another homeowner learn about spring torque the hard way. We keep common Clopay spring sizes on the truck, so same-day replacement across Long Beach is normal for us. Call (424) 688-6426 and we’ll give you a flat price for your specific door before we head over.

FAQs